Eight easy steps to clean and stain your deck using Resene Kwila Timber Stain
- Mix one part Resent Moss & Mould Killer to five parts clean water.
- Apply the solution generously to the deck and leave for 48 hours.
- Mix one part Resent Timber and Deck Wash to three parts water.
- Scrub the solution vigorously across the deck using a stiff bristled brush.
- Allow the wood to remain wet for 10-15 minutes before rinsing off with clean water. Allow to dry.
- Carefully stir the Resene Kwila Timber Stain with a paint stirrer.
- Apply one coat of Resene Kwila limber Stain to the deck, brushing in the direction of the grain. Allow to dry for 24 hours. Clean brush with Resene mineral turpentine.
- Apply a second coat of Resene Kwila Timber Stain to the deck, brushing in the direction of the grain. Again, allow 24 hours to dry. Clean brush with Resene mineral turpentine.
Finished result: Your deck is ready for you to enjoy.
Just as the bark of a tree protects the timber beneath, you need to make sure timber decks and furniture are well protected to keep them looking good and minimise permanent damage to the surface. We all know that our sun is harsh on skin – it is just as harsh on exterior timber surfaces.
Protecting exterior timber is as easy as 1 2 3: 1. Wash 2. Stain, oil or gel 3. Enjoy!
Always treat mould first as part of your prep using Resene Moss & Mould Killer. Never apply paint or stain over mould as it will just grow through. Simply dilute Resene Moss & Mould Killer, apply to your surface and leave, then scrub and wash off. For a general wash of all timber areas, use Resene Timber and Deck Wash. This will clean your deck, furniture, weatherboards or fence so it is ready for new stain, oil or paint. It is ideal for spring cleaning decks and furniture too, even if you are not staining or oiling.
- Protect, Recolour, Rejuvenate
Resene stains, gels, oils and paints not only help to protect your timber, but they can also help retain or rejuvenate the colour too.
Resene Timber and Furniture Gel – this product gives you the look of a stain, but it’s extra-thick nature means it’s much easier to apply to furniture and small wooden areas without unwanted drips and splashes. Available in a range of colors.
Resene Kwila Timber Stain – gives a rich Kwila brown finish to decks, furniture and doors. Resene Furniture and Decking Oil – ideal to give a natural looking finish to timber. Apply annually to keep timber looking good. Or choose from the Resene Woodsman stain range or Resene paint finishes for other options.
Always ensure new timber has at least one coat of stain or paint on it prior to using. This is especially important in food preparation or eating areas where food may be dropped as this can leave a permanent mark on bare timber. Ideally, after the first protective coat has been applied, leave new timber to weather for at least three months before staining or coating further. This allows time for the timber to ‘open up’ so that the stain or coating will penetrate or stick better. New timber can be very dense and stains will not penetrate as deeply as they will with well-weathered timber. It is important to either allow the timber to weather for a couple of months or scrub using Resene Timber and Deck Wash to ‘open up’ the timber surface and allow the selected product to soak in.
This may be an issue if your deck has a BBQ sitting on it or is a table, as dropped food, such as greasy sausages or meat, can stain the timber. If this is likely, stain as soon as practical. Kwila and some hardwoods leach tannins for the first few months when washed or rained on. This can stain concrete and pavers. It is best to wash until they stop leaching or leave on grass for a while until the colour has come out. Applying a stain or oil will not prevent this natural process from occurring.Going dark? Choose a Resene CoolColourTM If you’re planning a dark colour outside, choose a Resene CoolColourTM option if it’s available. A Resene CoolColour reflects more heat than a standard colour, helping to keep the surface cooler and helping to prevent warping and other timber damage.
Timbers vary greatly in their colour, hardness and grain. It always pays to test your chosen product on a representative piece of timber to ensure you are happy with the finish before starting on the full project.
Say no to clear finishes
Clear finishes outside provide little or no protection to your timber. If you want a natural look, opt for a stain or oil close as possible to the original colour. This will give you a natural look while still protecting the timber.
If your substrate is previously coated in a mineral oil based wood finish, it must continue to be coated in the same finish.
- Enjoy your newly stained or painted deck and furniture!
SIKKENS CETOL HLSe
Transparent, satin woodcare product for interior and exterior use. Its woodstain like qualities ensure timber grain remains highly visible. Cetol HLSe is microporous allowing the timber to breathe.
Use: Suitable for most types of timber. Used as a primer/basecoat for Cetol Filter 7 plus or Cetol Deck or Deck plus and as a stand alone 3 coat system on cladding, garden furniture, BBQ tables, handrails etc.
SIKKENS CETOL CLEARCOAT LB PLUS
Colourless, satin gloss, low build preservative for protected east or south facing exterior timber. Contains binary light stabilisers (improved UV resistance), based on alkyd resin. The wood grain remains visible. Microporous, resulting in a humidity-controlling system. Water repellent. Simple maintenance. Abrasion resistant (not scratch proof).
Use: As a primer/basecoat for Cetol Clearcoat HB plus or as a standalone 3 coat system on protected, south or east facing timber structures. As a maintenance system on intact – still sufficiently pigmented – Cetol HLSe coats. Brush application recommended.
SIKKENS CETOL DECK & DECK PLUS
Translucent satin topcoat for use on timber decks. Based on a special oil-alkyd resin combination and selected UV-absorbing pigments. Pigmented natural colour. Highly transparent; ensures optimum visibility of the wood grain. Withstands physical wear. Microporous; allows the wood to breathe. Weather resistant. Water repellent. Cetol Deck Plus has the same properties as Cetol Deck but includes a slip resistant additive.
Use: As a topcoat over Cetol HLSe to enhance the natural beauty of timber and to provide additional abrasion resistance. Brush application recommended.
SIKKENS CETOL FILTER 7 PLUS
Maximum durability. film forming, transparent, satin woodcare product based on alkyd resins with added UV filters for exterior use. Weather resistant and highly transparent, Cetol Filter 7 plus is a flexible coating which expands and contracts with the timber instead of forming a rigid shell on the surface. Cetol Filter 7 plus contains powerful UV filters and is microporous.
Use: As a topcoat over Cetol HLSe on most types of timber. Common areas of use are joinery, fascia, gables, garage and front doors etc.
SIKKENS CETOL CLEARCOAT HB PLUS
Colourless, satin gloss, high build, preservative for protected east or south facing exterior timber. Contains binary light stabilisers (improved UV resistance), based on alkyd resin. The wood grain remains visible. Microporous, resulting in a humidity-controlling system. Water repellent. Contains mould and algae inhibitors.
Use: As a topcoat over Cetol HLSe or Cetol Clearcoat LB plus on protected, south or east facing timber structures. As a maintenance system on intact – still sufficiently pigmented – Cetol HLSe, Cetol Novatech or Cetol Filter 7 plus coats. Brush application recommended.
Transparent, solvent borne, clear finish for interior wood surfaces. Accentuates the natural grain, colour and texture of all timbers and provides a hardwearing finish for doors, cabinets, furniture, etc. Abrasion resistant varnish. Resistant to water, soap, domestic chemicals and alcohol spills.
Use: Suitable for most types of timber, as a stand alone 3 coat system on bench tops, shelves, skirting, panelling, furniture, doors etc. Also commonly used as the finishing coats on timber that has been stained with Cetol HLSe.